Search results for "measurement technique"
showing 10 items of 13 documents
Measuring rill erosion using structure from motion: A plot experiment
2017
Abstract In this paper the results of a plot experiment on rill erosion are reported. The rill network, manually incised on the soil and further shaped by a clear inflow discharge, was surveyed using the three-dimensional photo-reconstruction (3D-PR) technique which allows to obtain a digital terrain model (DTM) by a large series of oblique images of the channel from consumer un-calibrated and non-metric cameras. The three-dimensional (3D) DTM and the quasi-tridimensional (2.5D) model were generated by Agisoft Photoscan software. For a single rill channel, the reliability of the 3D image-based ground measurements of morphological and hydraulic variables was positively tested by the correspo…
Glenoid bone loss in anterior shoulder dislocation: a multicentric study to assess the most reliable imaging method
2022
Purpose: The aim of this multicentric study was to assess which imaging method has the best inter-reader agreement for glenoid bone loss quantification in anterior shoulder instability. A further aim was to calculate the inter-method agreement comparing bilateral CT with unilateral CT and MR arthrography (MRA) with CT measurements. Finally, calculations were carried out to find the least time-consuming method. Method: A retrospective evaluation was performed by 9 readers (or pairs of readers) on a consecutive series of 110 patients with MRA and bilateral shoulder CT. Each reader was asked to calculate the glenoid bone loss of all patients using the following methods: best fit circle area on…
A REVIEW OF COLOR MEASURMENTS IN THE TEXTILE INDUSTRY
2016
Color is an important factor in the evaluation of aesthetic appearance and functionality of many products, but especially of textile industry ones. In textiles production process, color can be assessed in different stages: the selection of raw materials, the incoming item tests, the preparation of dyeing ingredients, the crocking resistance testing, the color fastness and in all stages, the quality control. Color evaluation can be done visually or using specialized test instruments such as colorimeters or spectrometers, therefore a high accuracy of measurements must be achieved. Standards describe different procedures and testing techniques depending on the product type and the quality leve…
EAGLE 2006 - Multi-purpose, multi-angle and multi-sensor in-situ and airborne campaigns over grassland and forest
2009
EAGLE2006 – an intensive field campaign for the advances in land surface hydrometeorological processes – was carried out in the Netherlands from 8th to 18th June 2006, involving 16 institutions with in total 67 people from 16 different countries. In addition to the acquisition of multi-angle and multi-sensor satellite data, several airborne instruments – an optical imaging sensor, an imaging microwave radiometer, and a flux airplane – were deployed and extensive ground measurements were conducted over one grassland site at Cabauw and two forest sites at Loobos and Speulderbos in the central part of the Netherlands. The generated data set is both unique and urgently needed for the developmen…
A field assessment of the Simplified Falling Head technique to measure the saturated soil hydraulic conductivity
2012
Abstract The Simplified Falling Head (SFH) technique to measure field saturated soil hydraulic conductivity, Kfs, has received little testing or comparison with other techniques. Different experiments were carried out to i) determine the effect of ring size on the measured conductivity; ii) compare the SFH and Pressure Infiltrometer (PI) techniques in a clay loam soil; and iii) evaluate the approach used in the SFH methodology to estimate the α* parameter. Sampling a relatively large number of sites allowed to detect statistically significant relationships between the Kfs values obtained with rings differing in diameter (0.15 and 0.30 m, respectively). The ring size effect was substantial (…
Using the simplified falling head technique to detect temporal changes in field-saturated hydraulic conductivity at the surface of a sandy loam soil
2007
Abstract Determining temporal changes in field-saturated hydraulic conductivity ( K fs ) is important for understanding and modeling hydrological phenomena at the field scale. Little is known about temporal variability of K fs values measured at permanent sampling points. In this investigation, the simplified falling head (SFH) technique was used for an approximately 2-year period to determine temporal changes in K fs at 11 permanent sampling points established at the surface of a sandy loam soil. Additional K fs measurements were obtained by the single-ring pressure infiltrometer (PI) technique to also compare the SFH and PI techniques. The lowest mean values of K fs , M ( K fs ), were det…
A Maximizing Hydraulic Radius (MHR) method for defining cross-section limits in rills and ephemeral gullies
2021
Abstract In this paper, a new method for determining the cross-section limits in rills and ephemeral gullies is proposed. This method is based on the estimate of the actual depth ha of each cross-section, which is the particular depth distinguishing the channel from the hillslope areas. The analysis showed that the actual depth corresponds to a particular bank slope sta occurring for the maximum value of the hydraulic radius R. The method was applied using a volumetric approach for calculating the hydraulic radius as the ratio between the volume of the whole investigated channel and its boundary lateral surface. The value of the bank slope st was derived by the DEM of the whole channel late…
Comparing two methods of analysis of single-ring infiltrometer data for a sandy – loam soil
2009
The single-ring pressure i n filtrometer (PI) with the steady-state Two-Ponding-Depth (TPD) applic ation method were developed to simulta neously determine the saturated soil hydraulic conductivity, K , and the α ⁎ -parameter in the fi eld. Methods of analysis of transient PI data are also available but they have received little testing so far. The transient WU method and the TPD method were compared for a sandy-loam soil. A linearization technique o f the in filtration curve yielded more reliable K fs fs and α ⁎ results (i.e., falling within expected ranges) than a non-linear optimization technique. The WU method gave both positive and reasonable K and α ⁎ values for all infi ltration tests. U…
Testing the use of an image-based technique to measure gully erosion at Sparacia experimental area
2017
The first part of this investigation was aimed at testing the use of a three‐dimensional (3D) digital terrain model and a quasi‐tridimensional (2.5D) digital elevation model obtained by a large series of oblique images of eroded channels taken from consumer un‐calibrated and non‐metric cameras. For two closed earth channels having a different sinuosity, the ground measurement of some cross sections by a profilometer (P) was carried out and their real volume was also measured. The comparison among the three methods (3D, 2.5D, and P) pointed out that a limited underestimation of the total volume always occurs and that the 3D method is characterized by the minimum difference between measured a…
Measurement techniques and modelling of multiphase systems.
2011
Multiphase systems are often encountered in process industry. Widely diffused applications and operations involve the contact between different phases (gas-solid, gasliquid, solid liquid, etc.) for different purposes, such as chemical reactions of physical operations (heat transfer, mass transfer). Multiphase flows are therefore one of the most frequent applied fields in chemical engineering. The present thesis is aimed at the development of experimental techniques for the investigation of multiphase flow in general, with particular focus on the analysis of gas-solid and gas-liquid systems. Notably, the development of image analysis techniques is the central thread of the present contributi…